Posted on

starting a pot seed

To employ water germination, fill a glass with tap water and let it sit until it reaches room temperature or around 65 degrees Fahrenheit. Add two to three plant seeds per cup and allow them to sit, watching for any changes. Change the water to fresh tap water every two days, making sure it stays at room temperature.

Germination itself is a crucial aspect of cannabis cultivation. The seed germination process is the foundation of every marijuana plant, and steps can be taken to boost successful popping. For example, some cultivators improve germination attempts by soaking seeds in 1% hydrogen peroxide or a compost tea for 12 hours beforehand to kill any dangerous pests.

Gently water the soil with a spray bottle and situate your pots under a fluorescent lamp. Keep seeds away from the windowsill, as the temperature is too volatile for germination. In general, you’ll want to keep the temperature in the range of 70 to 80 degrees Fahrenheit.

How to germinate seeds in water

The downside of water germination is that once they’ve popped, you’ll need to maneuver them into their growing medium manually. This is a delicate process, as germinating seeds are extra fragile, and any harm risks the development of your plants. Make sure to place the seed roots down in the soil when you transfer to a pot.

Use a spray bottle to moisten the paper towels and then store the cushioned seeds between two plates, under a face-down bowl, or gently place them in a plastic bag. Maintain a temperature of about 72 degrees Fahrenheit, keeping the paper towel wrapped seeds in the dark and away from a windowsill. In two to five days, the seeds will pop inside the paper towel sandwich and emit tiny roots, ready to plant when they reach about five millimeters in length.

To germinate seeds indoors, use any of the methods described above. Within a few days, you’ll have popped seeds ready to transfer to a growing medium.

The environment in which seeds germinate also plays a role in the outcome. While there are several different germination methods, each requires proper moisture, minimal handling, and warm springtime temperatures between 68-72 degrees Fahrenheit.

We like to use seedling pellets that are made of a mix of compressed peat moss and coco husk. To expand, soak it in water for 10 minutes. Once your seedling pellet has absorbed enough water and has expanded to its maximum size, drain off any excess water. The growing medium should be like a damp sponge that would not leave streaks on the table. Dig a small hole about 1/4 in deep for your seed. Use a spoon to lift the seed out of its bath. If it has popped out a taproot be careful not to damage it. Gently place the seed into the hole and lightly cover it with dirt from the pellet. Now that you have started the germination process, your seedling will come above ground within two weeks. The older the seed, the longer it takes for it to germinate.

Our favorite thing about starting from a seed, rather than a clone, is that you get to see the full life cycle and enjoy a plant that is unique, just like you. An entirely new genetic makeup will enter the world for the first time, and if you’re lucky, something remarkable might be born.

To accelerate germination, you are going to want to soak your seed in a small container with lukewarm water and place it in a dark and warm place for 12-24 hours, but no longer. By drenching the seed, it absorbs the water thoroughly, activating the germination process. Doing this also helps to loosen the shell as it becomes a little softer making it easier for the embryo to crack it open. When your seed sinks to the bottom it is ready to be planted, and sometimes the seed will pop out a small taproot. A seed can still be planted though if it does not sink.

2) Planting your seed

Seedlings require a medium amount of light in which it has enough to grow but not too much light that it gets burned. Leaving your seedling in direct sunlight will cause the leaves to curl, while too little light will cause the seedling to stretch. If growing outside, seedlings want to see a direct light source to stop them stretching. If inside, a sunny windowsill with more than half a day of sunlight works wonders. Otherwise, 18 in away from a growing light works excellently. Your seedling should not stretch more than 6 in at most. We’ll cover lighting in more depth in a later blog.

For young plants, it’s best to use bottled water as it has no chlorine added. If using tap water, let it sit for 24 hours before watering to dissipate any chlorine. Chlorine can also be eliminated by boiling for 20 minutes. Under normal conditions, after soaking your seedling pellet, it should contain all the moisture your plant needs before it comes above ground. As it grows, it will only need about a shot glass worth of water at most per week to keep the medium damp. Seedlings don’t drink a lot of water, which makes sense given their size. Your plant will do better in a growing medium which is damp. Overwatering is just as deadly as drying out.

Perhaps the most exciting stage, your baby will typically come above ground in 1-2 weeks. As your seedling comes above the soil, its shell might take a few days to fall off. It’s best to leave it alone, nature has the job covered. If it does not come above ground after about two weeks, the chance of success is dramatically reduced, and it’s best to try again. Even the best seeds have an 85% germination rate. When your seedling comes above ground, it is going to want to see a direct light source.

Starting from seed is a remarkable journey. Understanding the biology is one thing, but comprehending how a little miracle bean can turn into a gigantic tree that can affect your body and mind is nothing short of an evolutionary miracle. Or rather a co-evolutionary story of plant and human.

Germinating cannabis seeds doesn’t always go as planned. Some seeds will be duds. Others will be slow and take longer to sprout. But some will pop quickly and grow rapidly.

Aside from producing cannabis through seeds, or sexual reproduction, you can also reproduce the plant through cloning, or asexual reproduction. A clone is a cutting that is genetically identical to the plant it was taken from—that plant is known as the “mother.”

Additionally, every long-time grower will tell you that clones degrade over time.

Step 3

Because they grow and flower quicker, growers can fit in multiple autoflower cannabis harvests into the span of one regular harvest.

To create a dark, protected space, take another plate and flip it over to cover the seeds, like a dome.

As we’ve mentioned, cannabis is a dioecious plant, meaning male and female reproductive organs appear on different plants.

However, potency in autoflowering varieties has increased significantly since their initial introduction, with some breeders crossbreeding the low-THC ruderalis with other more potent varieties.